Ένα μέρος της κριτικής έχει μεταφραστεί αυτόματα.
Whow - this boards exceeded my expectations by far! - Easy to install and program with Arduino and the original libraries from Lilygo Homepage (use GxGDEH0213B72.h driver) - SD card interface - which I didnt expect on this board - LiPo management chip, just connect a 1s lipo and charge it - ePaper is pretty fast and has good contrast Thats exactly what I looked for to display my solar and smarthomes power status with a simple "out-of-the-box" board. Board is the perfect present also for every DIY Arduino freak... So I immediately ordered 2 more...
This is the third T5 I've bought and I'll probably buy more. It is unbelievable how versatile this gadget is. I even popped a fuse on one of them because I'm a bad engineer and it was very easy to bridge it with a blob of solder. The board worked perfectly after.
Perfect little board! Over the past few months I've tested every pin and feature and it all works. The partial refresh is nice, but if you use it more than a dozen times in a row without a full refresh, it can burn in a ghost image on the screen.
Display work perfect. I bought the module because I program PDA computers with reading barcodes and so I can generate those codes directly (via web) on the display, I do not have to print on paper. The sample programs work. Only refresh the display is 5-8sec.
https://github.com/ZinggJM/GxEPD
Γρήγορος Ελεγκτής, απότομη οθόνη, συμπεριλαμβανομένης της υποστήριξης μπαταρίας λιποαναρρόφησης. Όλα σε ένα συμπαγές πίνακα και με πολύ καλή ποιότητα παραγωγής. Το γραφικό περιβάλλον του Arduino μπορεί να χρησιμοποιηθεί για τον προγραμματισμό - η πρότασή μου!
Η παράδοση κράτησε περισσότερο από το "νωμένο Βασίλειο παρά από την Κίνα, αλλά η ποιότητα είναι πολύ καλή, η μονάδα λειτουργεί όπως περιγράφεται. Η αντίθεση και η προβολή είναι πολύ καλή. Ευχαρίστως και πάλι!
It's working. Overall quality is good. The received module differs from the photo, there is no LED's near the e-ink display. Typical power usage for this module is about 45-50 mA. When using WiFi (connect, send data frame, disconnect ) there is a current burst up to 150mA. In deep sleep, consumes 7.4mA.
display is working programming with the linked libraries is working
Το πακέτο ήρθε πολύ καλά προστατευμένο και έφτασε πριν από την προθεσμία. Η οθόνη έφερε την τελευταία εικόνα του προφορτισμένου προγράμματος και όταν συνέδεσα τη συσκευή ESP32 στην θύρα USB, εκτέλεσε σωστά το προφορτισμένο πρόγραμμα εργοστασίου. Ακολουθώντας τις οδηγίες του λογισμικού που παρέχεται από τη σελίδα Banggood, επαναπρογραμμάτισα το ESP32 με τις δικές μου πληροφορίες χωρίς καμία δυσκολία. Πολύ καλή αγορά σε πολύ καλή τιμή!!!